Many swaps finish same day, with scheduling typically within 24–48 hours in most seasons.
The Lennox EL296E stands out from conventional furnaces by offering adaptable heating capabilities that not only enhance comfort but also optimize energy use.
The Carrier Infinity® 96 Gas Furnace 59TN6 offers unparalleled comfort and efficiency for homes in Toronto.
Value-Smart Option
A contractor-grade, high-efficiency furnace tuned for balanced performance and fair pricing.
Right-size or we make it right.
No mess, no surprises. Written scope + fixed installed price.
Documented startup. You receive a commissioning checklist with readings.
Priority aftercare. Tune-ups, reminders, and responsive winter support.
Your Satisfaction is Guaranteed. Schedule
service today.
Your home is unique. Your furnace installation East York quote reflects:
Two-stage vs. modulating, and brand tier
Venting route, gas line upgrades, transitions/plenum work
Duct condition, return air sizing, balancing needs
Add-ons: humidifier, media filter/HEPA, HRV/ERV, smart thermostat
Site specifics: basement headroom, drain options, access/parking
We always show a good / better / best breakdown, including optional monthly payments.
A post-war bungalow near O’Connor-Parkview runs too warm upstairs and cool on the main. For this furnace installation East York project, we:
Right-size the furnace via Manual-J (no “BTU per sq. ft.” guessing)
Add a dedicated main-floor return to reduce stratification
Choose a two-stage, variable-speed model for quiet, even heat
Set fan profiles for low-noise circulation
Result: steadier temps, fewer starts/stops, lower noise, and happier gas bills.
8:00–9:00 AM — Arrival & Protection
Floor runners down, scope review, safety lock-out, utilities off.
Morning — Removal & Prep
Old unit out; venting, gas, and electrical reviewed. Custom plenum/transition fabricated as needed.
Midday — Set, Pipe, Wire
New furnace set; gas line verified; intake/exhaust routed with proper pitch and clearances; condensate trapped and pumped to an approved drain.
Afternoon — Commissioning
We document temperature-rise, ESP/airflow, gas manifold pressure, combustion/CO, safety controls, and thermostat calibration.
Wrap-Up — Homeowner Walkthrough
Filter sizes, maintenance intervals, warranty registration, and care tips. Clean site—like we were never there.
Right-size or we make it right.
No mess, no surprises. Written scope + fixed installed price.
Documented startup. You receive a commissioning checklist with readings.
Priority aftercare. Tune-ups, reminders, and responsive winter support.
Split systems & high-efficiency gas furnaces
Duct optimization, returns, zoning
Smart thermostats & IAQ (humidifiers, media filters, HRV/ERV)
Ductless/heat pumps for additions and top-up heat
Maintenance plans that protect warranties and efficiency
These are the most frequently asked questions about HVAC, Sizing, and More. Please feel free to contact us if you don’t see your question answered below.
Many swaps finish same day, with scheduling typically within 24–48 hours in most seasons.
Yes. We follow manufacturer specs and Ontario code, and guide you on any permits/inspections required for furnace installation East York projects.
It can. We measure ESP and choose a filter strategy that protects airflow—and your heat exchanger.
We run a Manual-J heat-loss calculation (insulation, windows, leakage, exposures, duct capacity) for precise furnace installation East York sizing.
Temperature-rise, gas manifold pressure, combustion/CO, ESP/airflow, safety controls, and thermostat calibration—documented in a written startup checklist for your records.
We don’t use “BTU per sq. ft.” rules of thumb. We perform a Manual-J heat-loss calculation that factors insulation levels, window/door U-values, air leakage, exposures, and duct design. Proper sizing prevents short-cycling, improves comfort, and protects the heat exchanger. For furnace installation Greater Toronto and furnace installation Toronto, we also confirm duct capacity so airflow (CFM) matches the selected furnace/coil.
ESP is the resistance your blower must push air against (measured in inches w.c.). High ESP from restrictive filters, undersized ducts, or a dirty coil reduces airflow, raises noise, and can overheat the heat exchanger. On install day we measure ESP with a manometer, target manufacturer-specified ranges, and correct issues (filter media, transitions, duct mods) to restore designed CFM.
Usually yes. 90%+ AFUE condensing furnaces use PVC/CPVC/PP venting with a dedicated combustion air intake. The condensate must be trapped and drained to an approved location (often with a condensate pump) and, where required, passed through a neutralizer before discharge. Vent terminations must meet clearance rules and be pitched correctly to prevent freezing and backflow.
A proper startup includes: temperature-rise verification, gas manifold pressure set-up, combustion analysis/CO check, ESP/airflow measurements, safety controls test (limit, pressure switch), flame sensor microamp check, thermostat calibration, and a written commissioning report. We perform and document all of the above on every furnace installation Toronto & GTA project.
If you’re comparing projects across multiple boroughs, see our broader furnace installation Greater Toronto guide for standards, timelines, and city-wide best practices.
External Static Pressure (ESP) Matters
High ESP from restrictive filters or undersized ducts kills airflow, raises noise, and stresses heat exchangers. On every furnace installation East York job we measure ESP with a manometer and correct bottlenecks.
For Saving Home Service Inc. is a Great Toronto Area-based HVAC company offering complete installation, service, and maintenance of Heating, Air conditioning installation, and Ventilation systems repair...
©2024, ForSaving. All rights reserved.
